Just how do you really feel in regards to Installing A Bathtub?
Installing a tub isn't exactly brain surgery, yet it does call for solid plumbing, woodworking, and in some cases, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably difficult job. If the old bathtub is readily easily accessible, the job can relocate speedily; if you need to open up a wall to eliminate the old bathtub as well as place the new tub, the job is much harder. In either situation, the task is within a home handyman's abilities, although you will certainly need a helper to move out the old bathtub and set in the brand-new one. See to it you have certified on your own for the job as well as fit trying it. Rather than employing a service provider to take over a halfway-completed task, it is better to think about using one prior to you begin. Possibilities are you might require a specialist plumber to make tube connections.
This short article will certainly aid you mount a brand-new bath tub in your shower room if you have actually already gotten a brand-new tub as well as do not require to change the plan of your previous water system pipelines.
Your tools and material list should make up the following:
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installation, then the first thing you should do is disconnect the supply of water. After doing so, switch on the taps to drain any type of water staying in the system. The procedure of eliminating the existing faucets can be rather troublesome as a result of the restricted access that is frequently the situation.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the faucets. Have a towel all set for the continuing to be water that will certainly come from the pipes. Once the supply pipes have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming throughout this procedure. As soon as the faucets have been removed, the holes in the bath/basin will need to be cleansed of any kind of old securing compound.
Before moving on to fit the brand-new faucets, compare the pipeline links on the old taps to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will need a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end provides a link to the existing supply pipes.
If you need to fit a monobloc, after that you will call for minimizing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin making certain that the washing machines are in area between the faucet as well as the sink. Secure the faucet in position with the manufacturer given backnut. When the tap is firmly in position, the supply pipes can be attached to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical tap adapters. The former type must be connected to the faucet ends first, tightening up only by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Installing the Tub
Using both wooden boards under its feet, position the bathtub in the called for setting. The wood boards are valuable in evenly spreading out the weight of the bathtub over the location of the boards rather than concentrating all the weight onto four tiny points.
The following goal is to make certain that the tub is leveled all round. This can be attained by inspecting the level and readjusting the feet on the bathtub until the level reads degree.
To mount taps, fit all-time low of the furthest adaptable tap port to the appropriate supply pipe by making a compression sign up with; then do the exact same for the other faucet.
Turn on the water and inspect all joints and new pipework for leakages and tighten them if required. Load the bathtub as well as additionally check the overflow electrical outlet and also the regular outlet for leaks.
Ultimately, fix the bath paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the bathtub must wait till the bathtub has been utilized a minimum of when as this will certainly settle it into its last placement.
Preparing for the Setup
First of all, the sustaining frame supplied with the bath must be fitted (if required) according to the producer's directions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is necessary to make sure that if the tap includes a plastic washer, it is fitted in between the bathroom and also the taps. On a plastic bath, it is also practical to fit a sustaining plate under the taps unit to prevent stress on the tub.
Fit the versatile faucet adapters to the bottom of both faucets making use of 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you use all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath should now be ready to be suited its last placement.
Tiling Around the Bath tub
In the location where the bath satisfies the tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the fitting can move sufficient to fracture a stiff seal, triggering the water to permeate the wall in between the bathroom as well as the tiling, causing problems with wetness as well as possible leakages to the ceiling below.
You can choose from a variety of coloured sealers to assimilate your fixtures and installations. They are offered in tubes as well as cartridges, and can securing spaces up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of drenched newspaper or soft rope. Remember to constantly fill up the bathtub with water prior to securing, to allow for the movement experienced when the bathtub is in use. The sealer can split fairly very early if you do not take into consideration this motion before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also conveniently readily available on the market. It is advisable to fit the floor tiles using waterproof or water resistant adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a serious reader about Tools You Need to Install a New Bathtub , I thought sharing that piece of content was valuable. You should take the opportunity to share this blog posting if you enjoyed it. I appreciate reading our article about Tools You Need to Install a New Bathtub .
Schedule Service Now